Skip to content

Filter bag · Ø 500 mm (19.7 in)

BAMATO AB2530FS filter bag, Ø 500 mm

A filter bag is a wear part, and a 500 mm (19.7 in) clamping ring is common enough that this one fits more machines than its own.

Woven replacement filter bag for a chip extractor, product photograph

BAMATO AB2530FS filter bag, Ø 500 mm

A filter bag is a wear part, and a 500 mm (19.7 in) clamping ring is common enough that this one fits more machines than its own.

Diameter
500 mm (19.7 in)
Height
About 850 mm (33.5 in)
Material
Woven filter fabric
Fitting
500 mm (19.7 in) clamping ring, no tools needed
Intended machine
BAMATO AB-2530
Part number
Not published
Amazon reference
B096M69YK3 (identical on 2 markets)
EAN
4260537612527
  • A 500 mm (19.7 in) ring is a common size, and the maker states it suits other machines built the same way
  • Woven fabric rather than plain cotton, so it survives repeated shaking out
  • A filter bag is not a dust class — the fine fraction passes straight through a woven bag

Best for: Replacing a split or clogged upper bag on a single-stage chip extractor

Search Amazon for this model

Specifications

Diameter
500 mm (19.7 in)
Height
About 850 mm (33.5 in)
Material
Woven filter fabric
Fitting
500 mm (19.7 in) clamping ring, no tools needed
Intended machine
BAMATO AB-2530
Part number
Not published
Amazon reference
B096M69YK3 (identical on 2 markets)
EAN
4260537612527

Every figure below is a manufacturer specification read off the listing itself. The judgments are ours.

What the specification says

A woven replacement filter bag, Ø 500 mm (19.7 in) and about 850 mm (33.5 in) tall, for the BAMATO AB-2530. It fits with the machine’s own clamping band and needs no tools. No part number on the listing.

What a bag does and does not do

The upper bag on a single-stage extractor is a filter and an exhaust. Air leaves through the weave, chips and coarse dust stay inside, and the bag gradually blinds as fine dust packs into the fabric — which is felt as a slow loss of suction rather than seen. Shaking it out restores most of it.

What it never does is hold the respirable fraction. That passes through the weave and back into the room, which is why a cyclone in front of the machine and a mask on your face are both still necessary.

Measure the ring, not the model

The maker states that the 500 mm (19.7 in) clamping ring is common enough that this bag suits other machines built to the same pattern, and that is broadly true of the single-stage extractor class — most of them are assembled from the same small set of parts under different badges. It is still worth a tape measure round your own ring and a check on the height, because a bag that is too tall drags on the floor and tears along the bottom seam within a season.

Availability

No such listing: the American Amazon shop answers the reference with a search box rather than a page.

Read from Keepa on the day this page was last revised; stock and price both move without notice.

What comes up most often

Does a better bag make the extractor safer?

No, and this is the distinction that matters most in the extraction family. A woven bag stops chips and coarse dust and passes the fine fraction — the part that stays airborne for hours and does the damage. Filtration class is a property of a cartridge or a fine filter, not of a chip bag, whatever the weave.

Will it fit a machine that is not a BAMATO?

Possibly, and the maker says so: many single-stage extractors use a 500 mm (19.7 in) clamping ring because the whole class is built from the same parts. Measure the ring on your own machine rather than trusting the model name, and check the height too — a bag that is too long drags on the floor and tears at the seam.

More extraction fittings

  • Fulton 11714 power tool hose kit with eight adapter fittings, product photograph

    Peachtree Woodworking Supply Fulton 11714 hose kit, 10 ft, 8 fittings

    A hand-tool hose with eight adapters, three of them stretchable — and the only listing here that publishes a fit warning.

    Hose
    10 ft long, 1-3/16 in outer diameter — 3.05 m (10 ft) × 30 mm (1.18 in), stated puncture resistant
    Fittings
    Eight: 2 small rubber thread-on, 2 ribbed rubber adaptors, 1 plug-in shop vacuum adaptor and 3 Sili Flex fittings · The eight are enumerated and the count agrees
    Silicone ends
    Stretchable silicone, stated to adapt to different dust ports — the only stretch fitting on this shelf
    Named tools
    Orbital sanders and biscuit joiners, stated
    Fit warning
    Stated: shop vacuum port sizes vary by manufacturer, and the images and dimensions should be reviewed carefully — the only fit warning published on this shelf
    Quantity
    1 hose and 8 fittings
    Part number
    11714
    Amazon reference
    B0FPNH1XWK
    EAN
    0817918025298
    • Enumerates all eight fittings, and the count agrees with the total
    • Stretchable silicone ends, which is the only real answer to a non-standard port
    • Thirty millimeters of hose will not serve a machine port

    Best for: A random orbital sander and a biscuit joiner on a shop vacuum, where no two ports are the same size

    ≈ $32
    Check price on Amazon
  • Fulton four inch blast gates, six pack, product photograph

    Fulton Woodworking Tools 12109 blast gates, 4 in, 6 pack

    Six gates, which is how many a ducted shop needs — and a published stop, which is the complaint the shelf already had.

    Diameter
    4 in nominal · No actual diameters are published
    Ports
    Tapered on both sides, stated so hoses slip on and can be clamped, and stated to accept some tapered fittings
    Gate
    A sliding gate with a built-in stop, stated so it will not slide out when fully opened — the only stop published on this shelf
    Function
    Stated as a shut-off valve: closed, air does not flow; open, dust is collected · Stated that one gate per machine concentrates airflow on the machine in use
    Material
    ABS
    Quantity
    6 gates
    Not supplied
    Hoses and hose clamps, both stated sold separately
    Part number
    12109
    Amazon reference
    B0BG8X6NPN
    EAN
    0817918023386
    • Six gates, which is one per machine in a real workshop
    • A built-in stop, which answers the complaint the published single gate on this shelf records
    • No actual diameters published, only nominal four inches

    Best for: A workshop with fixed four-inch ducting to several machines — one gate at each

    ≈ $30
    Check price on Amazon
  • Transparent 100 mm dust extraction hose, product photograph

    Miko Ø 100 mm extraction hose, 2.5 m

    The hose is what limits most extraction systems, not the machine. Getting the diameter right matters more than getting the extractor right.

    Diameter
    100 mm (3.94 in)
    Length
    2.5 m (8 ft)
    Wall
    Transparent
    Amazon reference
    B07Y3Q9TPB (identical on 3 markets)
    EAN
    4260289832471
    • 100 mm (3.94 in) matches the ports on planers, table saws and band saws
    • Transparent, so a blockage is visible instead of guessed at
    • Not sold in Britain, France or the United States

    Best for: Connecting a chip collector to a 100 mm (3.94 in) machine port

    Search Amazon for this model

Elsewhere in the workroom

  • FOXBC 12.5 inch planer knives for DeWalt DW734, set of three, product photograph

    FOXBC FOX7342, 12-1/2 in HSS knives for DW734, set of 3

    The DW734 set, sold explicitly as costing less than having the old ones sharpened.

    Length
    12-1/2 in — 318 mm
    Width
    Not published by the maker.
    Thickness
    Not published by the maker.
    Material
    M2 high-speed steel, stated for longer cutting life
    Type
    Double-edged reversible, stated in the maker's own quotation marks
    Setting
    Not published by the maker. · The maker publishes locator holes on two of its other listings on this shelf
    Economics
    Stated a cost-effective alternative to sharpening — the only listing on this shelf to make that comparison
    Quantity
    3 knives, in a plastic case
    Replaces
    DeWalt DW7342, for the DW734
    Part number
    FOX7342
    Amazon reference
    B07DH6D7NY
    EAN
    0703931966734
    • Names M2 as the steel grade
    • Makes the honest argument: new knives cost less than sharpening old ones
    • Publishes only the length — no width and no thickness

    Best for: A DeWalt DW734, where the old knives are blunt and sharpening quotes have been obtained

    ≈ $28
    Check price on Amazon
  • FOXBC 13 inch planer knives for DeWalt DW735, set of three, product photograph

    FOXBC FOX735, 13 in HSS knives for DW735, set of 3

    Three double-edged M2 knives with locator holes — which is what setting knives without a gauge requires.

    Length
    13 in, published — 330 mm (13 in) · The POWERTEC knives for the same DeWalt part on this shelf publish 13-1/8 in
    Width
    7/8 in — 22.2 mm
    Thickness
    1/16 in — 1.6 mm
    Material
    M2 laminated high-speed steel, stated to stay sharper and last longer than conventional knife materials
    Type
    Reversible, double sided, with honed cutting edges
    Setting
    Machined locator holes, stated to align the knives on the cutterhead during a change
    Quantity
    3 knives
    Replaces
    DeWalt DW7352, for the DW735 and DW735X
    Part number
    FOX735
    Amazon reference
    B07DH5FVNF
    EAN
    0703931966888
    • Publishes all three dimensions, which is the whole specification of a knife
    • Locator holes, so the knives set themselves rather than needing a gauge
    • Thirteen inches here against 13-1/8 on the POWERTEC set for the same part

    Best for: A DeWalt DW735 or DW735X, changed without a setting gauge

    ≈ $30
    Check price on Amazon
  • FOXBC 82 mm TCT carbide planer blades, pair, product photograph

    FOXBC 82 × 29 × 3 mm TCT, pair

    A thicker, wider 82 mm (3.23 in) blade than the rest of this shelf — and the longest machine list on it.

    Length
    82 mm (3.23 in) — 3-1/4 in
    Width
    29 mm (1.14 in) · Five times the 5.5 mm (0.22 in) of the other 82 mm (3.23 in) blades on this shelf
    Thickness
    3 mm (0.12 in) · Two and a half times the 1.2 mm (0.05 in) of the other 82 mm (3.23 in) blades here
    Material
    TCT tungsten carbide
    Claims
    Stated to last up to 30 per cent longer and to be 10 per cent sharper than standard tungsten carbide blades · The HZ blades on this shelf publish the same two percentages, word for word
    Quantity
    2 blades, in a plastic case
    Fits
    Fourteen machines named: Makita 1900B, N1900B, KP0800K, KP0810, 1100, 1902, 1923B, 1923H, KP0800, XPK01Z and XPK02Z; DeWalt D26676, DW6655, DW677, 678 and 680K; Bosch 1594 and PA1205; and Ryobi — the longest fitment list on either half of this shelf
    Part number
    FOXBC-3 1/4
    Amazon reference
    B07H49849M
    EAN
    6971007720809
    • Publishes all three dimensions, and they are different from every other 82 mm (3.23 in) blade here
    • Names fourteen machines, which no other listing on this shelf approaches
    • Twenty-nine millimeters wide is not interchangeable with the 5.5 mm (0.22 in) blades on this shelf

    Best for: One of the fourteen named planers, where the head takes a solid 3 mm (0.12 in) blade and not a shim

    ≈ $10
    Check price on Amazon

All extraction fittings