Belt, disc, spindle & drum · review
The cheapest belt-and-disc combination here, and the machine that stops you sanding curves by hand.
The end of it The cheapest way to sand accurately rather than approximately. Its specification is a mystery and its job is not.
Every figure is a manufacturer specification, read off the listing itself, and the judgments are ours — drawn from how the specification behaves in this class of machine and from what long-term owners consistently report. Where a figure is missing, we say so rather than fill it in.
A bench belt and disc sander, part number 4419257. Einhell publishes no motor rating, no belt dimensions and no disc diameter on this listing — which matters because belt size determines what abrasive you can buy for it.
Each grit removes the scratches of the one before it. Skip a step — 80 straight to 180 — and the 180 paper polishes the 80-grit scratches instead of removing them. They are invisible on bare timber and obvious the moment a finish goes on, under a raking light, at which point the only fix is to start again at 80.
The progression costs one extra sheet. The mistake costs the panel.
Belt length and width, and disc diameter. Not because they change what the machine does, but because they decide what consumables fit it. A belt size that is common — 915 × 100 mm (36 × 3.94 in) is the usual one at this class — means cheap abrasive from anyone; an unusual size means buying from one supplier forever.
The Scheppach on this page publishes 915 × 100 mm (36 × 3.94 in) and a 150 mm (5.91 in) disc. This one does not, and it is the single question to ask before buying.
Read on the day this page was built: $360 at the American Amazon shop.
Read from Keepa on the day this page was last revised; stock and price both move without notice.
Prices quoted in this text were read on 2026-08-12. The live price is at the top of the page.
| Type | Bench belt and disc sander |
|---|---|
| Part number | 4419257 |
| Amazon reference | B09HQYCYFG (identical on 6 markets) |
| EAN | 4006825649987 |
No. We searched for the 400 and the listing that came back carries part number 4419257 and reads TC-US 380. Different machine, so this is a review of the one that exists at this reference.
Because they do opposite jobs. The disc cuts hard and leaves a curved scratch pattern, so it is for outside curves and quick removal against the table. The belt runs straight and is for flats and inside curves over the end roller. Owning one and not the other means doing half the jobs badly.
A listing is not an offer: the reference exists on these stores, availability changes daily.
6.9/ 10
The cheapest way to sand accurately rather than approximately. Its specification is a mystery and its job is not.
Sanding to a line on small parts, where hand sanding is slow and imprecise
Listed because the blade or part names this saw.
Specifications: the manufacturer sheet for woodworking machines and the matching Amazon product page. Prices and availability: Keepa. Every figure on this page names its source.
12 V · Ø 125 mm (4.92 in) · L-BOXX 136 · no price, no barcode
A bundle we cannot price, cannot verify and cannot find in any market but one — which is the whole review.
Best for: Nobody, until the listing carries a price and a barcode
5 in pad · 3 A · 8,000–12,000 OPM · counterweight · dust-sealed switch
The only random orbit sander on either half of this shelf with a price on its listing — and it publishes an orbit range.
Best for: Finishing a surface before a finish goes on it, with a DEWALT extractor already in the shop
≈ $79
100 × 610 mm (3.94 × 24 in) belt · portable · the same price everywhere
A 100 mm (3.94 in) portable belt sander with a decades-old part number, priced within €10 across the whole of Europe.
Best for: Leveling glued-up panels, doors and floors — flat work at speed
≈ $420
