Skip to content

HSS · matched pair

Scheppach HSS planer knives, 260 mm, pair

Planer knives are sold in pairs for a reason, and fitting one new knife alongside a worn one is the classic way to ruin a surface.

Scheppach HSS planer knives, product photograph

Scheppach HSS planer knives, 260 mm, pair

Planer knives are sold in pairs for a reason, and fitting one new knife alongside a worn one is the classic way to ruin a surface.

Length
260 mm (10.2 in)
Material
HSS
Quantity
2
Part number
3902202701
Amazon reference
B00R6TOZ04 (identical on 6 markets)
EAN
4046664000310
  • Supplied as a matched pair, which is how they must be fitted
  • One reference and one EAN across all six markets
  • HSS dulls faster than carbide on abrasive or reclaimed timber

Best for: Replacing worn knives on a 260 mm (10.2 in) planer thicknesser

≈ $89
Check price on Amazon

Specifications

Length
260 mm (10.2 in)
Material
HSS
Quantity
2
Part number
3902202701
Amazon reference
B00R6TOZ04 (identical on 6 markets)
EAN
4046664000310

Every figure below is a manufacturer specification read off the listing itself. The judgments are ours.

What the specification says

260 mm (10.2 in), HSS, supplied as a pair. Part number 3902202701.

Setting them is the job, not buying them

A straight-knife cutterhead needs each knife set to the same height, parallel to the outfeed table, usually with a magnetic gauge or a straight edge. Getting it wrong shows up as snipe, ripple or a step at the end of every board.

This is precisely the frustration a helical cutterhead removes — see the planer hub — and it is the reason so many owners eventually pay to convert.

Saws this fits

What comes up most often

Why must both knives be changed together?

Because they must sit at exactly the same cutting circle. A new knife next to a worn one projects further, so it takes the entire cut on its own — it dulls at several times the normal rate, and it leaves a ripple pattern that owners routinely mistake for a bearing fault.

HSS or carbide?

HSS is cheaper, takes a keener edge and can be resharpened. Carbide lasts far longer on abrasive material — MDF, reclaimed timber, anything with grit in it — and cannot practically be resharpened at home. For clean solid timber, HSS is the sensible choice.

More planer knives

  • POWERTEC 13 inch planer knives for DeWalt DW735, set of three, product photograph

    POWERTEC 128000, 13-1/8 in HSS knives for DW735, set of 3

    The same DeWalt replacement as the FOXBC set here, published an eighth of an inch longer.

    Length
    13-1/8 in, published — 333 mm (13.1 in) · The FOXBC knives for the same DeWalt part on this shelf publish 13 in
    Width
    7/8 in — 22.2 mm
    Thickness
    1/16 in — 1.6 mm
    Material
    High-speed steel, stated for hardened sharpness, temperature protection and wear resistance · No grade is named
    Type
    Dual cutting edges with a reversible profile, stated to double the lifespan
    Setting
    Machine locator holes, stated for precise alignment
    Quantity
    3 knives
    Replaces
    DeWalt DW7352, for the DW735 and DW735X
    Part number
    128000 · The title also gives 12800, one digit shorter
    Amazon reference
    B005NYWNBW
    EAN
    0736815000002
    • Publishes all three dimensions, with the length to the eighth
    • Locator holes for alignment during a change
    • Thirteen and an eighth here against 13 on the FOXBC set for the same part

    Best for: A DeWalt DW735 or DW735X, with the existing knife measured first

    ≈ $26
    Check price on Amazon
  • Reversible 210 mm planer knives, product photograph

    Turmfalke CENTROFIX/CENTROSTAR 210 mm reversible knives

    Double-edged knives on a self-setting head: turn them round when they dull, and no gauge is needed at all.

    Length
    210 mm (8.27 in)
    Material
    HSS
    Type
    Double-edged, reversible
    Cutterhead
    CENTROFIX / CENTROSTAR
    Amazon reference
    B0CBQF4SSB (identical on 4 markets)
    EAN
    4099544011555
    • Two cutting edges per knife — flip rather than replace
    • Self-setting on the matching head, so no gauge and no measuring
    • Only fits CENTROFIX/CENTROSTAR-type heads — check yours

    Best for: Planers with a self-setting reversible cutterhead

    Search Amazon for this model
  • Ten square carbide inserts for woodworking tools, product photograph

    CDBP 14 × 14 × 2,0 mm carbide inserts, 10 pack

    Four cutting edges per insert and ten inserts in the box — provided the seat and the screw in your tool are the ones these were made for.

    Size
    14 × 14 × 2.0 mm (0.55 × 0.55 × 0.08 in)
    Cutting angle
    30°
    Fixing
    Single countersunk hole
    Grade
    BK10UF solid carbide
    Edges
    4 per insert
    Quantity
    10
    Part number
    14×14×2mm (0.55 × 0.55 × 0.08 in)-30°
    Amazon reference
    B09KBDVMS9 (identical on 5 markets)
    EAN
    0761594655068
    • Four usable corners per insert, so ten inserts are forty edges
    • Solid carbide rather than a brazed tip
    • The screw thread and the seat geometry are not published, and both decide fitment

    Best for: Turning tools and cutterblocks that are specified for a 14 × 14 × 2.0 mm (0.55 × 0.55 × 0.08 in) square insert

    Search Amazon for this model

Elsewhere in the workroom

  • POWERTEC abrasive cleaning stick, single, product photograph

    POWERTEC 71002 cleaning stick, 8-1/2 in

    The single stick — and the cheapest way onto this shelf, at a higher price per stick than the two-pack beside it.

    Quantity
    1 stick
    Stick size
    8-1/2 × 1-1/2 × 1-1/2 in, published — about 19 cubic inches of rubber
    Material
    All-natural rubber, stated professional grade
    Removes
    Sawdust, pitch, gum, glue and other residue, stated without damaging the grit
    Method
    Held against the abrasive while the sander is running, per the maker
    Named uses
    Sanding belts, disc sanders, drum sanders, skateboard grip tape, rubber-bottomed shoes
    Not for
    Plastic, and conveyor-feed type sanders — stated by the maker · Stated to work best on cured or dry residue
    Part number
    71002
    Amazon reference
    B00AJW0CY8
    EAN
    0736815004703
    • The least expensive item on the American half of this shelf
    • Publishes its size as three figures and its two exclusions
    • Costs more per stick than the two-pack of the same stick on this shelf

    Best for: One sanding machine, and the smallest sum that gets a cleaning stick into the workshop

    ≈ $10
    Check price on Amazon
  • POWERTEC abrasive cleaning sticks, two-pack, product photograph

    POWERTEC 71002-P2 cleaning stick, 8-1/2 in, 2 pack

    Two sticks instead of one, from a listing identical to its single-stick sibling in every word but the quantity.

    Quantity
    2 sticks
    Stick size
    8-1/2 × 1-1/2 × 1-1/2 in, published — about 19 cubic inches of rubber per stick
    Material
    All-natural rubber, stated professional grade
    Removes
    Sawdust, pitch, gum, glue and other residue, stated without damaging the grit
    Method
    Held against the abrasive while the sander is running, per the maker
    Named uses
    Sanding belts, disc sanders, drum sanders, skateboard grip tape, rubber-bottomed shoes
    Not for
    Plastic, and conveyor-feed type sanders — stated by the maker · Stated to work best on cured or dry residue
    Part number
    71002-P2
    Amazon reference
    B099WMPH2W
    EAN
    0843441111450
    • Publishes the stick size as three figures, which lets the rubber be compared
    • The only listing on this shelf to publish what it is not for
    • Its five published features are its single-stick sibling's, word for word

    Best for: A workshop with a belt sander and a disc sander, where a stick should live beside each

    ≈ $16
    Check price on Amazon
  • Transparent polyurethane dust extraction hose with steel spiral, product photograph

    JLXJYS Transparent PU extraction hose

    A tough transparent hose in a dozen diameters on one listing — which means the diameter you get is the one you remember to select.

    Wall
    Polyurethane, 1.5 mm (0.06 in)
    Reinforcement
    Copper-plated steel spiral
    Compression ratio
    3:1
    Temperature range
    −40 °C (-40 °F) to +90 °C (194 °F)
    Diameter
    Selected on the listing — 25 to 600 mm (0.98 to 23.6 in) are offered
    Length
    Cut to length
    Part number
    145263
    Amazon reference
    B0F9WZSCFS (identical on 5 markets)
    EAN
    7086207184470
    • Transparent, so a blockage is seen rather than diagnosed
    • A steel spiral at a 3:1 compression ratio, so it stores short and will not collapse
    • A dozen diameters share one listing — the €65 applies to one of them

    Best for: Replacing a split or opaque hose on an extractor, in whatever diameter the port takes

    Search Amazon for this model

All planer knives

Prices quoted in these summaries are dated readings. The live price is shown next to each product.