Holding the work · review
Five hundred pounds as a table and a thousand as a sawhorse, with four clamps and four bench dogs in the box.
The end of it The highest table rating and the only adjustable height here, with eight named accessories in the box.
Every figure below names its source. Each one is a manufacturer specification read off the listing itself. The judgments are ours.
As a table, and as a sawhorse. Both published.
The difference is where the load goes. On the table the load sits on the clamping surface — a pair of jaws on a frame, and the jaws are the limit. As a sawhorse it sits across the top rails and straight down the legs, which is the strongest path through any frame.
So the same object carries twice as much in the configuration where nothing has to hold anything.
The WORX bench on this shelf publishes the same pair at 300 and 1,000: same architecture, same sawhorse figure, a table rating two thirds lower.
Thirty to thirty-five inches — 762 to 889 mm (30 to 35 in), and the only adjustable height on either half of this shelf.
A fixed bench is set at the height its owner planes at. A folding one is used for sawing on site, assembling on a drive and clamping in a garage, and those want different heights.
Eight hundred and sixty millimeters is about where a hand plane works. A sawing trestle wants less. This spans both.
The published Wolfcraft page on this shelf is credited for the neighboring feature: a height-adjustable foot, which is what makes a folding table stable on a workshop floor.
Two 12 inch medium-duty bar clamps. Two 6 inch light-duty. Two large bench dogs. Two small. Two safety straps.
That is the most complete list on either half of this shelf, and the reason it matters is in the published Sjöbergs Smart Workstation page’s cons: clamps to fix it down are not included, and it does nothing without them.
A clamping bench that arrives with its clamps works on the day it arrives.
A bench is judged on three things and only one of them is usually published.
Mass is what stops the bench moving when a plane is pushed along a board. Rigidity is what stops the top flexing under a mallet. Racking is the sideways parallelogram collapse that every four-legged frame wants to do, and it is resisted by stretchers and by the top being bolted down rather than resting.
A load rating is not any of the three — it says what the bench will hold standing still. The published Bosch PWB 600 page on this shelf names the figure that actually matters and its absence: no clamping capacity, which is a bench’s only real specification.
Which on a bench sold on folding into a car are the two figures a buyer wants.
The WORX bench on this shelf publishes 30 pounds and a 31 by 25 inch surface. The published Keter table publishes 910 by 555 by 755 mm (29.7 in).
This publishes six heights and eight accessories, and not how big it is.
Read on the day this page was built: $170 at the American Amazon shop.
Read from Keepa on the day this page was last revised; stock and price both move without notice.
Prices quoted in this text were read on 2026-10-07. The live price is at the top of the page.
| Type | Two-in-one: a clamping work table and a sawhorse, switchable |
|---|---|
| Load rating | 500 lb as a table and 1,000 lb as a sawhorse — 227 and 454 kg (1000.9 lb), both published |
| Height | Six settings from 30 to 35 in — 762 to 889 mm (30 to 35 in), the only adjustable height on this shelf |
| Frame | Aluminum legs, stated for superior support |
| Supplied | Two 12 in medium-duty bar clamps, two 6 in light-duty bar clamps, two large bench dogs, two small bench dogs and two safety straps — the most complete accessory list on either half of this shelf |
| Holding | Quick clamps and holding pegs, stated |
| Folding | Folds flat, stated for a car, a garage or a storage room |
| Weight | Not published by the maker. |
| Surface size | Not published by the maker. |
| Part number | 99214AJ.JP |
| Amazon reference | B09XT8D9NY |
| EAN | 0044295992145 |
Because the load goes to a different place. As a table the load sits on the clamping surface, which is a pair of jaws on a frame, and the jaws are the limit. As a sawhorse the load sits across the top rails and straight down the legs, which is the strongest path through any frame. So the same object carries twice as much in the configuration where nothing has to hold anything. The WORX bench on this shelf publishes the same pair of figures at 300 and 1,000 — same architecture, same sawhorse rating, and a table rating two thirds lower.
For a folding bench, more than for a fixed one. A fixed bench is set at the height its owner planes at; a folding one is used for sawing on site, assembling on a drive and clamping in a garage, and those want different heights. Thirty to thirty-five inches is 762 to 889 mm (30 to 35 in), which spans most of the useful range — a hand-plane bench is usually near 860 and a sawing trestle lower. It is the only adjustable height on either half of this shelf, and the published Wolfcraft page here is credited for the related feature: a height-adjustable foot, which is what makes a folding table stable on a workshop floor.
Eight accessories, each named: two 12 inch medium-duty bar clamps, two 6 inch light-duty bar clamps, two large bench dogs, two small bench dogs and two safety straps. That is the most complete list on either half of this shelf, and it matters because of what the published Sjöbergs Smart Workstation page says in its cons: clamps to fix it down are not included, and it does nothing without them. A clamping bench that arrives with its clamps is a bench that works on the day it arrives.
Site work and a shared garage, where the bench has to fold and the clamps have to come with it
Amazon reports what buyers took in the month before this page was last checked: at least 500.
The figure is a floor, rounded by Amazon, and read through Keepa — it says what buyers picked, not what a maker claims.
Specifications: the manufacturer sheet for woodworking machines and the matching Amazon product page. Prices and availability: Keepa. Every figure on this page names its source.
Folding bench · adjustable clamping top
The folding bench that has been in every garage for fifty years — and still the cheapest way to hold work at a sensible height.
Best for: A small or shared space where the bench has to disappear between jobs
≈ $350
Wood top · metal frame · one market · no barcode
A €217 Bosch workbench with a wooden top, a metal frame, and not one published dimension, weight or capacity.
Best for: A German buyer who has seen one in person and knows what they are getting
60 in · 330 lb capacity · rubberwood in the title and acacia in the bullet · drawer and shelf
A workbench whose title says rubberwood and whose first feature says acacia — two different trees.
Best for: A garage bench with a drawer, by somebody who will ask which timber arrives
≈ $330
